1.Radio Equipment Directive (RED)
The Radio Equipment Directive (RED) is an European Union directive to ensure that radio equipment, including wireless devices and telecommunications terminal equipment, is compliant with safety and health requirements and does not interfere with other devices that are operating on the same frequency.
2. RED products covered
Below are some of typical products we specialize in. It’s important to note that the list below is not exhaustive. Not sure if your product requires RED certification? Please 填寫我們的簡短表格，我們的專家將很樂意為您提供進一步的協助。
- Short-range device (SRD): remote control toy cars, remote control alarm systems, remote control doorbells, remote control switches, wireless mouse, wireless keyboard…
- Professional/private mobile radio (PMR): professional wireless walkie-talkie, wireless microphone…
- Cordless telephone: CT0, CT1;
- Integrated services digital network (ISDN);
- Digital enhanced cordless telecommunications (DECT);
- GSM/CDMA cell phone;
- Bluetooth devices: Bluetooth earphones…
- Data transmission equipment operating in the frequency range < 9 KHz;
- Radio broadcast receiver equipment;
- …
It’s important to note that the list above is not exhaustive, and the requirement for RED certification can vary based on the specific features and capabilities of a device. If a device emits radio frequency radiation or uses wireless technology, it’s advisable for manufacturers or importers to consult with the Notified Body or a qualified testing laboratory to determine whether RED certification is necessary for their particular product.
GTG Group’s testing laboratories are A2LA accredited, and our team is always available for any general inquiries, or technical discussions regarding compliance testing/certification. Speak to a GTG Group expert by 填寫我們的簡短表格 今天！
3. RED testing items, testing standards, materials required, certification processes and requirements for test samples
Testing items varies depending on the products. For testing items on specific product, please 填寫我們的簡短表格, our expert will be glad to assist you further. Below are some of typical testing items for RED:
- Electromagnetic compatibility (EMC) testing;
- Low voltage directive (LVD) testing;
- Radio frequency (RF) testing according to European Telecommunications Standards Institute ( ETSI) standards;
- Permitted spectrum in EU
- CTR (TBR) testing;
- Electrical safety testing (SAR assessment)
- …
Below is a list of RED testing standards (LVD excluded) we’re capable of. And our team is always available for any general inquiries, or technical discussions regarding the following RED testing standards. Not sure what standard or standards apply to your product? Please 填寫我們的簡短表格，我們的專家將很樂意為您提供進一步的協助。
- 125KHz RF ID: EN 300330; EN 301489-1/-3; EN 62311;
- 13.56MHz RF ID: EN 300330; EN 301489-1/-3; EN 62479;
- 27MHz: EN 300220-1/-2; EN 301489-1/-3; EN 62479;
- 433MHz: EN 300220-1/-2; EN 301489-1/-3; EN 62479;
- BT (2.4GHz), Zigbee, WiFi: EN 300328; EN 301489-1/-17; EN 62479 or EN 62311;
- Wireless Charging Products: EN 303417; EN 301489-1/-3; EN 62311;
- WiFi (5GHz), Single Band, Without DFS: EN 301893; EN 301489-1/-17; EN 62311;
- WiFi (5GHz), Dual Band, Without DFS: EN 300440; EN 301489-1/-17; EN 62311;
- WiFi (5GHz), Tri-band, With DFS: EN 301893; EN 301489-1/-17; EN 62311;
- 5GHz WiFi (Full Frequency Bands) + 2.4GHz WiFi: EN 301893/300328/300440; EN 301489-1/-17; EN 62311;
- 5.8GHz Products: EN 300440; EN 301489-1/-3; EN 62311.
所需材料因產品而異。有關特定產品的詳細所需材料，請 填寫我們的簡短表格, our expert will be glad to assist you further. Below are some of typical required materials for RED certification:
- 使用者手冊；
- 電路原理圖;
- Block diagram: all the crystal oscillator and crystal frequency must be shown and consistent with the circuit diagram;
- Schematic diagram: the number of crystal oscillators, crystal frequency and crystal location must be consistent with the block diagram;
- 標籤;
- Technical parameters of wireless module: frequency range, number of frequency bands, maximum emission power, antenna gain, modulation…
- …
Below are the general application steps for achieving RED certificate. Have questions or not sure where to start? Please 填寫我們的簡短表格，我們的專家將很樂意為您提供進一步的協助。
- 將測試樣品送到我們的實驗室；
- Perform testing and prepare for the report;
- Issue the certificate by Guangdong GTG Testing Technology Co., Ltd. (formerly Anci);
- If request a certificate issued by Notified Body, then all the materials and the report will be sent to the Notified Body for examination and approval. This will take a while.
Guangdong GTG Testing Technology Co., Ltd. (formerly Anci)’s laboratories are accredited by A2LA. This means we’re authorized to perform RED testing and write test reports accordingly.
- 射頻定頻樣機一台、普通樣機一台；
- 定頻樣機與多頻道產品進行測試；
- If it is a single frequency channel prototype, please provide a continuous emission and continuous receiver one.
5. 價格和交貨時間
You will never pay for services that you don’t need! GTG Group provides a customized quote which are tailored to each client's needs and budget. Furthermore, we can expedite the certification process by leveraging modern technologies that ensure you receive the RED certificate in a reasonably short time frame compared with the average industry time.
然而，測試和認證的成本和交付時間根據產品的複雜性和測試要求而有所不同。 GTG 集團提供免費諮詢來評估您的需求並提供如何開始合規的建議。今天透過以下方式聯絡我們 填寫我們的簡短表格！
6. A2LA accreditation documents
When you choose the GTG Group for testing and certification, you can be confident that you are working with a trusted and reliable partner.
Our laboratory is accredited by A2LA. This means we're authorized to perform RED testing and write test reports accordingly. Testing scope we specialize in: information technology (IT) products, audiovisual (AV) products, lighting products, small home appliances, power supplies, electric personal transportation vehicles, batteries...
7. 為什麼選擇我們？
GTG集團成立於2012年，是中國獨立的ISO/IEC 17025認可的產品測試和認證服務提供商，為多種產品提供全面的測試和監管認證服務。我們的目標是認證您的產品並確保其符合監管標準，以幫助您進入全球市場。
