1.Radio Equipment Directive (RED)
The Radio Equipment Directive (RED) is an European Union directive to ensure that radio equipment, including wireless devices and telecommunications terminal equipment, is compliant with safety and health requirements and does not interfere with other devices that are operating on the same frequency.
2. RED products covered
Below are some of typical products we specialize in. It’s important to note that the list below is not exhaustive. Not sure if your product requires RED certification? Please 간단한 양식을 작성해 주세요, 당사 전문가가 기꺼이 추가 지원을 해드릴 것입니다.
- Short-range device (SRD): remote control toy cars, remote control alarm systems, remote control doorbells, remote control switches, wireless mouse, wireless keyboard…
- Professional/private mobile radio (PMR): professional wireless walkie-talkie, wireless microphone…
- Cordless telephone: CT0, CT1;
- Integrated services digital network (ISDN);
- Digital enhanced cordless telecommunications (DECT);
- GSM/CDMA cell phone;
- Bluetooth devices: Bluetooth earphones…
- Data transmission equipment operating in the frequency range < 9 KHz;
- Radio broadcast receiver equipment;
- …
It’s important to note that the list above is not exhaustive, and the requirement for RED certification can vary based on the specific features and capabilities of a device. If a device emits radio frequency radiation or uses wireless technology, it’s advisable for manufacturers or importers to consult with the Notified Body or a qualified testing laboratory to determine whether RED certification is necessary for their particular product.
GTG Group’s testing laboratories are A2LA accredited, and our team is always available for any general inquiries, or technical discussions regarding compliance testing/certification. Speak to a GTG Group expert by 간단한 양식 작성 오늘!
3. RED testing items, testing standards, materials required, certification processes and requirements for test samples
Testing items varies depending on the products. For testing items on specific product, please 간단한 양식을 작성해 주세요, our expert will be glad to assist you further. Below are some of typical testing items for RED:
- Electromagnetic compatibility (EMC) testing;
- Low voltage directive (LVD) testing;
- Radio frequency (RF) testing according to European Telecommunications Standards Institute ( ETSI) standards;
- Permitted spectrum in EU
- CTR (TBR) testing;
- Electrical safety testing (SAR assessment)
- …
Below is a list of RED testing standards (LVD excluded) we’re capable of. And our team is always available for any general inquiries, or technical discussions regarding the following RED testing standards. Not sure what standard or standards apply to your product? Please 간단한 양식을 작성해 주세요, 당사 전문가가 기꺼이 추가 지원을 해드릴 것입니다.
- 125KHz RF ID: EN 300330; EN 301489-1/-3; EN 62311;
- 13.56MHz RF ID: EN 300330; EN 301489-1/-3; EN 62479;
- 27MHz: EN 300220-1/-2; EN 301489-1/-3; EN 62479;
- 433MHz: EN 300220-1/-2; EN 301489-1/-3; EN 62479;
- BT (2.4GHz), Zigbee, WiFi: EN 300328; EN 301489-1/-17; EN 62479 or EN 62311;
- Wireless Charging Products: EN 303417; EN 301489-1/-3; EN 62311;
- WiFi (5GHz), Single Band, Without DFS: EN 301893; EN 301489-1/-17; EN 62311;
- WiFi (5GHz), Dual Band, Without DFS: EN 300440; EN 301489-1/-17; EN 62311;
- WiFi (5GHz), Tri-band, With DFS: EN 301893; EN 301489-1/-17; EN 62311;
- 5GHz WiFi (Full Frequency Bands) + 2.4GHz WiFi: EN 301893/300328/300440; EN 301489-1/-17; EN 62311;
- 5.8GHz Products: EN 300440; EN 301489-1/-3; EN 62311.
제품에 따라 필요한 재료가 다릅니다. 특정 제품에 대한 자세한 필수 자료를 원하시면 간단한 양식을 작성해 주세요, our expert will be glad to assist you further. Below are some of typical required materials for RED certification:
- 사용자 설명서;
- 회로도;
- Block diagram: all the crystal oscillator and crystal frequency must be shown and consistent with the circuit diagram;
- Schematic diagram: the number of crystal oscillators, crystal frequency and crystal location must be consistent with the block diagram;
- 상표;
- Technical parameters of wireless module: frequency range, number of frequency bands, maximum emission power, antenna gain, modulation…
- …
Below are the general application steps for achieving RED certificate. Have questions or not sure where to start? Please 간단한 양식을 작성해 주세요, 당사 전문가가 기꺼이 추가 지원을 해드릴 것입니다.
- 테스트 샘플을 우리 연구실로 보내십시오.
- Perform testing and prepare for the report;
- Issue the certificate by Guangdong GTG Testing Technology Co., Ltd. (formerly Anci);
- If request a certificate issued by Notified Body, then all the materials and the report will be sent to the Notified Body for examination and approval. This will take a while.
Guangdong GTG Testing Technology Co., Ltd. (formerly Anci)’s laboratories are accredited by A2LA. This means we’re authorized to perform RED testing and write test reports accordingly.
- RF 고정 주파수 프로토타입 1개와 일반 프로토타입 1개
- 고정 주파수 프로토타입은 다중 주파수 채널 제품으로 테스트됩니다.
- If it is a single frequency channel prototype, please provide a continuous emission and continuous receiver one.
5. 가격 및 리드타임
You will never pay for services that you don’t need! GTG Group provides a customized quote which are tailored to each client's needs and budget. Furthermore, we can expedite the certification process by leveraging modern technologies that ensure you receive the RED certificate in a reasonably short time frame compared with the average industry time.
그러나 테스트 및 인증에 소요되는 비용과 소요 시간은 제품의 복잡성과 테스트 요구 사항에 따라 달라집니다. GTG 그룹은 귀하의 요구 사항을 평가하고 규정 준수를 시작하는 방법에 대한 조언을 제공하기 위한 무료 상담을 제공합니다. 오늘 저희에게 연락주세요 간단한 양식 작성!
6. A2LA 인증 서류
테스트 및 인증을 위해 GTG 그룹을 선택하면 신뢰할 수 있는 신뢰할 수 있는 파트너와 협력하고 있다는 확신을 가질 수 있습니다.
Our laboratory is accredited by A2LA. This means we're authorized to perform RED testing and write test reports accordingly. Testing scope we specialize in: information technology (IT) products, audiovisual (AV) products, lighting products, small home appliances, power supplies, electric personal transportation vehicles, batteries...
7. 왜 우리를 선택합니까?
2012년에 설립된 GTG 그룹은 중국의 독립적인 ISO/IEC 17025 공인 제품 테스트 및 인증 서비스 제공업체로서 광범위한 제품에 대한 포괄적인 테스트 및 규제 인증 획득 서비스를 제공합니다. 우리의 목표는 귀사의 제품을 인증하고 규제 표준 준수를 보장하여 귀사가 전 세계 시장에 진출할 수 있도록 돕는 것입니다.
